Fisher Price Baby Toy 79534 User Manual

BOUNCE ’N PLAY  
ACTIVITY DOME  
Model Number: 79534, 79545, 79546  
Please save these instructions for future reference.  
Tool needed for assembly: Phillips Screwdriver (not included).  
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.  
Product features may vary from picture above.  
 
PARTS  
Metal Canopy Stay  
®
®
Pad  
2 Covers  
3 Toys  
(Toys may  
be different  
than shown)  
2 Base Wires  
Base  
Spring - 4  
Plastic Mesh Cover Stay  
13  
M5 x 1 /16" Screw - 2  
CAUTION  
In its unassembled state, this  
5
M6 x 1 /8" Screw - 8  
product contains small parts.  
Adult assembly is required.  
M5 Lock Nut - 2  
M6 Lock Nut - 8  
SHOWN ACTUAL SIZE  
3
 
ASSEMBLY  
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.  
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.  
Never substitute parts.  
Button Hole  
Plastic Mesh  
Frame  
Cover Stay  
3
1
Middle Hole  
Middle Hole  
Mesh Cover  
Frame Tube  
Frame Tube  
• Position the ends of the frame tubes against the middle holes  
in a frame.  
Base  
• Open the base and position it upright on a flat surface,  
as shown.  
• Locate the end of the base with the mesh cover. Insert the  
entire plastic mesh cover stay into one of the button holes  
in the mesh cover.  
M6 Lock Nut  
4
• Be sure to tuck the plastic mesh cover stay away from the  
button hole in the mesh cover.  
Frame Tube  
Canopy Tunnel  
2
Frame Tube  
Metal  
Canopy  
Stay  
Frame  
Protruding  
Side  
5
M6 x 1 /8" Screw - 4  
M6 Lock Nut - 4  
• Insert an M6 x 15/8" screw through each frame tube and into  
the frame.  
• Fit an M6 lock nut (so that the protruding side is toward the  
fabric) into each middle opening on the back of the frame.  
• Insert the metal canopy stay through the canopy tunnel.  
4
 
ASSEMBLY  
Metal Canopy Stay  
5
7
Cover  
Upper  
Hole  
• Tighten the screws with a Phillips screwdriver. Do not  
over-tighten.  
Slot  
Tab  
• Repeat this procedure to attach the other ends of the frame  
tubes to the frame on the other side of the base.  
Protruding  
Side  
Frame  
13  
M5 x 1 /16" Screw -2  
M5 Lock Nut -2  
6
Lower Hole  
Spring  
• Position one end of the metal canopy stay against the upper  
hole in a frame.  
• Insert an M5 x 113/16" screw through the hole in the cover.  
• Fit the end of the screw through the hole in the metal canopy  
stay and into the upper hole in the frame.  
• Push on the cover to insert and “snap” the tab on the cover into  
Lower Hole  
the slot in the frame. Make sure you hear a “snap.  
Base Wire  
• Fit an M5 lock nut (so that the protruding side is toward the  
fabric) into the upper hexagonal opening on the back of  
the frame.  
Spring - 4  
• Tighten the screw with a Phillips screwdriver. Do not  
over-tighten.  
• Repeat this procedure to attach the other end of the metal  
canopy stay and the remaining cover to the frame on the other  
side of the base.  
Protruding Side  
M6 Lock Nut - 4  
5
M6 x 1 /8" Screw - 4  
• Position the base wires around the base so that the ends point  
upward and are against the lower holes in a frame.  
• Place a spring onto an M6 x 15/8” screw.  
• Insert the M6 x 15/8" screw with spring through a base wire and  
into the frame.  
• Fit an M6 lock nut (so that the protruding side is toward the  
fabric) into each lower hexagonal opening on the back of  
the frame.  
• Tighten the screws with a Phillips screwdriver. Do not  
over-tighten.  
• Repeat this procedure to attach the other ends of the base  
wires to the frame on the other side of the base.  
5
 
ASSEMBLY  
USE  
To Unfold  
Toys  
Canopy  
Fasteners  
8
1
Pad  
Fastener  
Sides of Base Wire  
• Position the product upright on a flat surface.  
• Grasp both sides of a base wire.  
®
• Pull both sides of the base wire outward and then let the base  
wire rotate down.  
Note: If the base wire does not freely rotate down, pull the sides  
of the base wire further outward.  
• Fasten the pad fasteners to the base fasteners.  
• Lift the canopy.  
• Attach the toys to the canopy fasteners.  
IMPORTANT! Assembly is now complete, but Bounce ‘n Play  
Activity Dome is not ready for use. Please refer to the Use  
instructions, on this page, beginning with step 2.  
2
Frame  
Groove  
Groove  
Sides of Base Wire  
• Lift the product up slightly so that each side of the base wire  
“snaps” into the groove in each frame. Make sure you hear  
a “snap.  
6
 
USE  
Using the Mesh Cover  
Zipper  
3
Mesh Cover Up  
5
Canopy Up  
Frame  
Groove  
Base Wire  
®
• Push down on the product to be  
sure each side of the base wire is  
in the correct position. The base  
wire should rest in the groove in  
each frame.  
• Adjust the canopy and mesh cover up.  
• While holding the mesh cover up, fasten the zipper closed.  
Correct  
To Fold for Portability  
• Repeat Use steps 1 - 3 to unfold  
the other base wire.  
Using the Canopy  
6
Canopy Up  
Frame  
4
Canopy  
Down  
Groove  
Groove  
Sides of Base Wire  
• Grasp both sides of a base wire.  
®
• While lifting the product up slightly, pull both sides of the  
base wire outward to remove the base wire from the groove  
in each frame.  
• Adjust the canopy up or down.  
7
 
USE  
CARE  
The pad and toys are machine washable. Wash the pad and toys  
separately in cold water on the gentle cycle. Do not use bleach.  
Tumble dry separately on low heat and remove promptly. The  
fabric and frame may be wiped clean using a mild cleaning  
solution and a damp cloth.  
Base Wire  
7
• Rotate the base wire up.  
• Repeat this procedure to fold the other base wire.  
If you have any questions about this product:  
In CANADA: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga,  
Ontario L5R 3W2. Questions? 1-800-567-7724.  
In GREAT BRITAIN: Mattel U.K., Ltd., Helpline: 01628 500303.  
In AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,  
Richmond, Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812  
(valid only in Australia).  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.  
79534F-0920  
©2000 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.  
Printed in Hong Kong  
 

Exido Scale 246 020 User Manual
Extron electronic Network Router FOX Matrix 3200 User Manual
Extron electronic Speaker System SI 3 Black User Manual
Ford Car Stereo System AM FM Stereo Radio Cassette User Manual
Freecom Technologies DVD Recorder DVD RW Recorder User Manual
GE Bread Maker 106732 User Manual
GE Convection Oven PT916SM User Manual
Gemini Musical Instrument UMX 3 User Manual
Generac Power Systems Portable Generator 005261 1 005262 1 User Manual
Goldstar Microwave Oven MA 2005ST User Manual